Design and Implementation of Evanescent Mode Waveguide Filters Using Dielectrics and Additive Manufacturing Techniques
Design and Implementation of Evanescent Mode Waveguide Filters Using Dielectrics and Additive...
Pons-Abenza, Alejandro;Garcia-Barcelo, Jose-Maria;Romera-Perez, Antonio;Alvarez-Melcon, Alejandro;Quesada-Pereira, Fernando;Hinojosa-Jimenez, Juan;Guglielmi, Marco;Boria, Vicente;Arche-Andradas, Lara
JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 1 Design and Implementation of Evanescent Mode Waveguide Filters Using Dielectrics and Additive Manufacturing Techniques Alejandro Pons-Abenza, Student Member, IEEE, Jose-Mar ´ ´ ıa Garc´ ıa-Barcelo, ´ Antonio Romera-Perez, ´ Alejandro Alvarez-Melcon, Senior Member, IEEE, Fernando Quesada-Pereira, Member, IEEE, Juan Hinojosa-Jimenez, ´ Senior Member, IEEE, Marco Guglielmi, Fellow, IEEE, Vicente Boria, Fellow, IEEE, and Lara Arche-Andradas, Abstract—In this contribution, we describe the design of Furthermore, the most common implementation of microwave bandpass ﬁlters using evanescent mode waveguides and dielectric waveguide ﬁlters is based on CNC machining of aluminum. resonators implemented with additive manufacturing techniques. Unfortunately, however, CNC machining techniques have lim- Two C-band Chebyshev evanescent mode waveguide ﬁlters of itations in terms of manufacturing certain complex geometries order ﬁve have been designed using a low cost commercial . dielectric material (ABSplus), widely used by Fused Deposi- tion Modeling (FDM) 3D printers. The housings of the ﬁlters In this context, therefore, emerging Additive Manufacturing have been manufactured using traditional computer numerical (AM) techniques are becoming very attractive to produce novel control (CNC) machining techniques. Practical manufacturing passive ﬁlter geometries and microwave devices , . Using considerations are also discussed, including the integration of AM techniques complex shapes can, in fact, be very easily dielectric and metallic parts. We ﬁrst discuss two breadboards manufactured . Using thermoplastic as base material, for using two different resonator geometries. We then demonstrate how different transfer functions can be easily implemented by instance, and using subsequent metallization of the hardware, changing the 3D printed parts in the same metallic housing. one can dramatically reduce the overall mass of the ﬁlter Breadboards show fractional bandwidths between 3% and 4.6% structure . In  the metallization of the walls is achieved with return losses better than RL = 18 dB, and spurious free using an automated deposition process of conductive silver ranges of SFR = 1 GHz. Insertion losses are better than ink. A similar, although more elaborated strategy is used in IL = 4:3 dB. Even though dielectric losses from the plastic material are shown to be high, the measured results are quite , where air channels are implemented into the walls of the satisfactory, thereby clearly showing that this strategy maybe plastic pieces, which are then ﬁlled with a liquid metal. It useful for the fast production of low cost microwave ﬁlters is also interesting to remark that a similar concept was used implementing complex geometries. in  to build a waveguide switch. In this case the switch Index Terms—3D-printers, ABSplus, additive manufacturing, operation is achieved by pumping in and out the liquid metal dielectric resonators, evanescent mode waveguides, microwave through plastic tubes. Additionally, smart optimization of the ﬁlters, selective laser melting. shape of traditional implementations can signiﬁcantly reduce the Insertion Losses (IL) of the ﬁlters . Other authors have tried direct geometrical modiﬁcations on the cavity resonator I. I NTRODUCTION itself, using curvilinear shapes, leading to new resonators with HE design of ﬁlters in waveguide technology remains signiﬁcant improvements in terms of unloaded quality factors one of the most important activities in the microwave (Q ). Interesting works in this direction are the spherical engineering ﬁeld . Waveguide ﬁlters are, in fact, used in resonators proposed in , , or the use of complex the input/output stages of many systems, for both space and curvilinear shapes as proposed in . ground application, where low loss and high-power handling The implementation of dielectric resonators has also been are critical requirements . In addition, physical constrains recently explored in the context of AM. A list of thermo- such as low volume and small footprint are usually required. plastics and ceramics showing good dielectric properties can, in fact, be found for many FDM or Stereo-lithography (SLA) Manuscript received xx xx, 2019; revised xx xx, xxxx. This work is supported in part by Thales Alenia Space (Tres Cantos, commercial 3D-printers , . Various strategies have also Madrid, Spain), and by the grant TEC2016-75934-C4-4-R in collaboration been discussed to incorporate AM dielectrics into a waveguide with TEC2016-75934-C4-1-R of MEC, Spain. ﬁlter structure. An interesting example can be found in , A. Pons, J.M. Garc´ ıa, A. Romera, A. Alvarez, F. Quesada are with Department of Information and Communication Technologies (DTIC), Elec- where a TM-mode dielectric resonator based on alumina with tromagnetism Applied to Telecommunications research group (GEAT) at tan < 0:002 and 9:9 is used to directly print a second Technical University of Cartagena (Murcia, Spain). order ﬁlter. After the hardware has been printed, the external J. Hinojosa is with Department of Electronics, Projects and Computer Technologies at Technical University of Cartagena (Murcia, Spain). faces are metallized to build the lateral walls of the structure. M. Guglielmi and V. Boria are with ITEAM (Instituto de Telecomuni- The ﬁlter shows good performance in terms of losses, but with caciones y Aplicaciones Multimedia) at Technical University of Valencia slight frequency deviations due to the lack of accuracy of the (Valencia, Spain). L. Arche is with Thales Alenia Space Spain (Tres Cantos, Madrid, Spain). AM process. An alternative solution is to design the dielectric arXiv:1909.00723v1 [eess.SP] 2 Sep 2019 A JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 2 of this hybrid manufacturing strategy is also demonstrated in this paper. Namely, several ﬁlters with different transfer functions can be easily implemented using the same external aluminum housing. What is needed is just the design of new dielectric parts, which are then manufactured with the 3D printer. Following this approach, only one common external housing is manufactured with CNC machining techniques, while high ﬂexibility can be obtained by producing several low cost plastic pieces to implement different transfer functions. Overall, the measured performance of the manufactured prototypes is good, thereby fully conﬁrming the practical feasibility of the new concepts proposed in the paper. II. F ILTERS DESIGN Fig. 1. 2D sketches of the evanescent mode ﬁlters proposed in this paper. (a) Design with air holes inside a dielectric block ﬁlling a waveguide section The ﬁlters used in this work to demonstrate the hybrid with reduced width (air-holes ﬁlter). (b) Design with dielectric posts inside manufacturing strategy are two 5-pole Chebyshev ﬁlters with an otherwise empty evanescent waveguide section ( -posts ﬁlter). 20 dB return loss (RL). The ﬁlters have been designed at C- band with a center frequency f = 3:68 GHz and a bandwidth BW = 120 MHz (fractional bandwidth FBW 3:2%). The resonators from a single piece of plastic, which is then fastened ﬁlters are designed using an in-line topology, since no cross- in the ﬁlter using the metallic parts of the coupling windows. couplings will be considered for simplicity. It is important to This strategy is demonstrated in , where the dielectric note, however, that cross coupled structures can also be easily resonators are printed from a single plastic bar, following an implemented. The coupling matrix, which is the same for both in-line topology, or in , where a more complex connection ﬁlters, has all elements equal to zero, except for couplings mechanism between resonators is proposed. along the in-line channel (M )  i;i+1 In this context therefore, we contribute to the state-of-the- art of AM manufacturing of waveguide ﬁlters by showing how M = M = 1:0137; M = M = 0:8653; S1 5L 12 45 the two evanescent mode ﬁlter designs shown in Fig. 1 can be (1) M = M = 0:6357: 23 34 manufactured using 3D printing techniques. The objective of this paper is to compare two different solutions for evanescent 2D sketches of the proposed ﬁlters are presented in Fig. 1. mode ﬁlters that can be rapidly and inexpensively manufac- A standard WR-229 waveguide has been used for the in- tured with 3D-printing using commercial AM dielectric mate- put/output waveguide ports (a = 58:17 mm, b = 29:083 mm). rials. The ﬁlter structures discussed in this paper combine AM The ﬁrst ﬁlter, shown in Fig. 1(a), consists of a dielectric parts for the dielectric elements, with conventional aluminum piece placed inside a reduced width waveguide section, with a CNC machining, thus leading to a hybrid manufacturing series of air holes. This ﬁlter uses the fundamental TE mode, strategy. Following this strategy, the metallic parts of the which can propagate in the dielectric ﬁlled waveguide section, structure are kept simple, while complex geometries may be while the air holes, where the fundamental mode is below easily manufactured for the dielectric elements. cut-off, are used to implement the coupling elements between The dielectric elements proposed in this work are imple- resonators. The width of the waveguide section is reduced to mented with a low cost commercial ABSplus plastic from avoid the propagation of higher order modes, when it is ﬁlled Stratasys, with relative dielectric constant = 3:55 . This with the dielectric material. The physical separation between material has recently become widely available in low cost air holes [l in Fig. 1(a)] controls the resonant frequency of 3D printers. The ﬁrst solution, shown in Fig. 1(a), consists each resonator. The air holes are implemented as elliptical of a ﬁlter with a reduced width, dielectric-ﬁlled rectangular cylinders, and their dimensions [r according to Fig. 1(a)] are waveguide, where inter resonator couplings are implemented used to control the coupling level between adjacent resonators. with elliptical air holes (subsequently referred to as the air- Consequently, for the design of our 5th-order ﬁlter, a total hole ﬁlter). The complementary approach is followed in the of six air holes are required. With this arrangement, the second design, where several elliptic dielectric post resonators input/output couplings are controlled with the sizes of the ﬁrst are placed inside an empty evanescent rectangular waveguide and last air holes. However, the step discontinuity needed for section, as shown in Fig. 1(b) (subsequently referred to as the implementing the reduced width waveguide section will also -post ﬁlter). r affect this coupling. The two structures proposed in this work have been manu- As it can be observed in Fig. 1(a), the dielectric piece factured with a hybrid strategy. Namely, the 3D printed plastic is longer than the waveguide section (l ). The extra length ev pieces have been manufactured using an FDM 3D printer, (l ) will facilitate the alignment of the dielectric piece with while the aluminum housings have been manufactured using the external metallic housing. We also veriﬁed that this extra standard CNC machining. This strategy allows for a fast and dielectric section helps to increase the input/output coupling low cost implementation of the ﬁlters, although at the expense levels of the ﬁlter. However, the extra length (l ) cannot be of somewhat higher insertion losses. An additional beneﬁt very large, as this area may become resonant due the formation A JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 3 of an air-dielectric discontinuity. As it will be shown later in 18 18 this paper, this suggests that, in practice, a trade-off is needed to adjust the length l . 16 16 The second solution proposed in this paper is shown in Fig. 1(b). In this case, instead of ﬁlling the whole waveguide with a dielectric material, only several cylindrical dielectric 14 14 posts are placed inside an empty waveguide section. With this arrangement the fundamental TE mode is below cut- 12 12 off in the evanescent waveguide section, and the dielectric posts become resonant. Consequently, the dimensions of these posts [r according to Fig. 1(b)] control the resonant frequency 10 10 of each resonator, while the physical distances between adja- cent posts [l in Fig. 1(b)] control the coupling level by i;i+1 8 8 proximity. For our 5th-order ﬁlter, a total of 5 dielectric posts 0.4 0.6 0.8 1 1.2 are required. Intuitively, this solution may be more compact, Normalized coupling level M ij since less posts (as compared to air-holes) are required to implement the same frequency response. For this solution, Fig. 2. Normalized inter-resonator coupling curves for the two proposed the input/output couplings are implemented with the distance conﬁgurations. Legend refers to Fig. 1(a) (air-holes) and to Fig. 1(b) ( - posts). For this test (a = 30 mm). ev between the ports and the ﬁrst (or last) dielectric resonator [l in Fig. 1(b)]. However, the maximum coupling that can s1 be achieved is strongly determined by the step junction needed It is well known that for the input/output coupling, a to form the evanescent waveguide section. different procedure must be followed. This procedure consists It is important to note that in both structures shown in Fig. 1, of adjusting the external quality factor (Q ) of a single ext the cylinders are of elliptical shape, and we have ﬁxed the resonator to the value calculated from the coupling matrix, radius along the x-axis to r = 14 mm. This assures a 1 mm namely ,  gap between the waveguide side walls and each post, for a width of the evanescent waveguide section of a = 30 mm. Q = : (4) av ext M BW S1 For the design process, a variation of the classical even/odd A doubly-terminated resonator structure can be used for this analysis technique has been used . This approach is based purpose. This will allow the computation of the Q as a ext on calculating the even-odd resonant frequencies (f , f ) e o function of the physical parameter of the ﬁlter related to the of two symmetric coupled resonators working at the center input/output couplings. For our two conﬁgurations, the key frequency (f ). The frequency scaled coupling coefﬁcient can parameters are the elliptical semi-axis of the ﬁrst air-hole (r ) then directly be computed from these two frequencies as , 1 [air-hole ﬁlter, Fig. 1(a)] and the distance to the ﬁrst resonator  2 2 (l ) [dielectric post ﬁlter, Fig. 1(b)]. The corresponding results s1 f f e o k = ; (2) sc for each structure are shown in Fig. 3. Similarly to Fig. 2, two 2 2 f + f e o different ordinate axes have been used to show both results on and the normalized coupling coefﬁcient, which is directly the same plot. related to the coupling matrix values given in (1), can be As we can see from the Q curves shown in Fig. 3, the ext calculated as ,  slopes are similar. However, the structure with dielectric posts can achieve lower Q values. Therefore, this structure is ext k = M = k : (3) more suitable to implement ﬁlters with wider passbands as norm ij sc BW compared to the ﬁlter with air-holes. This behavior is enhanced The normalized coupling values (M ), obtained for the two by the fact that the coupling distance l in Fig. 1(b) can ij s1 types of resonators we propose, are presented in Fig. 2. The be made slightly negative, meaning that the ﬁrst and last same ﬁgure is employed to present the results obtained for resonators are slightly introduced in the port section [l of port the two conﬁgurations discussed in this paper, by using two Fig. 1(b)]. independent vertical axes. For the conﬁguration shown in Another interesting conclusion can be pointed out from the Fig. 1(a), the coupling is given as a function of the air-hole plot shown in Fig. 3. For narrowband ﬁlters, where larger semi-axis (r ), while the length (l ) is used for the second Q values are needed, the ﬁlter with dielectric posts has i ij ext conﬁguration shown in Fig. 1(b). the potential to be more compact. As shown in the plot, large The levels computed for M are suitable in both cases Q values require smaller coupling distances (l ) for the ij ext s1 to obtain the ﬁlters with the initial speciﬁcations. It can dielectric posts ﬁlter, as compared to the diameter (2 r ) of be observed that, to implement an equal coupling level, the the air-holes ﬁlter (l < 2 r ). For instance, to synthesize s1 1 conﬁguration with dielectric posts will in general be smaller Q = 100, a coupling length l = 16 mm is needed, while ext s1 than the one with air-holes (l < r ). This indicates that, for the axis of the air-hole needs to be larger (2 r = 20 mm). This ij i 1 equal responses, the solution with dielectric posts will result conﬁrms the behavior already observed for the inter-resonator in a more compact structure. couplings in Fig. 2. For the same in-band response, more Coupling length l ij Coupling length r i A JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 4 TABLE I 25 25 F INAL DIM ENSIONS OF THE DESIGNED AIR-HOLES FILTER ACCORDING TO F IG. 1(A). 20 20 Var. Value (mm) Var. Value (mm) Var. Value(mm) l 10 l 0 r 4:859 port 1 1 15 15 l 7 l 22:11 r 14:54 2 2 l 258:847 l 23:23 r 16:86 ev 3 3 l 292:847 l 23:13 r 14 tot 4 x 10 10 TABLE II 5 5 F INAL DIM ENSIONS OF THE DESIGNED DIELECTRIC POSTS FILTER ACCORDING TO F IG. 1(B). 0 0 Var. Value (mm) Var. Value (mm) Var. Value (mm) l 15 l 0:439 r 13:619 port s1 1 -5 -5 l 275:016 l 24:6 r 14:208 tot 12 2 0 50 100 150 l 245:016 l 28:474 r 14:219 ev 23 3 External Q-factor (Q ) ext Fig. 3. External quality factor (Q ) for the two proposed evanescent ﬁlters. ext coupling. In addition, we have veriﬁed that it is not convenient The legend refers to Fig. 1(a) (air-holes) and to Fig. 1(b) ( -posts). For this to take very large values for the length l . This is because test we have ﬁxed: a = 30 mm, l = 7 mm, l = 0 mm. ev d 1 the junction may become resonant in the area between the waveguide step and the air-dielectric discontinuity. Taking into consideration all the practical aspects discussed so far, and the r = 10mm behavior shown in Fig. 4, an optimum value of l = 7 mm r = 11mm has been selected for the designs presented in this paper. r = 12mm Using the data shown in Fig. 2 and Fig. 3, the initial r = 13mm dimensions for the two ﬁlters can now be easily obtained. r = 14mm The ﬁnal optimized ﬁlter dimensions are shown in Table I r = 15mm and Table II, respectively. The wide band responses for both 400 ﬁlters are presented in Fig. 5. The results shown have been obtained with the full-wave simulator HFSS . As we can see, the responses of the two ﬁlters are very similar, both inside and outside the passband. The out of band responses indicate that the spurious free ranges (SFR) of both ﬁlters are also very similar. In particular, the ﬁrst spurious band appears 2 4 6 8 10 at f 4:8 GHz, giving SFR 1 GHz. sp Except for the insertion losses (IL), that will be discussed Length l (mm) in the next section, the results obtained indicate that the Fig. 4. Q values for the air-holes ﬁlter as a function of the extra length ext (l ), for various values of the input semi-axis (r ). For this test we have ﬁxed: d 1 a = 30 mm, l = 0 mm. ev 1 -10 compact structures can be obtained with the conﬁguration based on dielectric posts. -20 As already mentioned, the input coupling of the air-hole ﬁlter is also affected by the extra length (l ) used to align -30 the dielectric piece with the external housing. In order to study this effect, we present in Fig. 4 the Q values for ext -40 this ﬁlter as a function of the extra length (l ) for various values of the input air-hole semi-axis (r ). As we can see, the -50 Q value decreases when the length l is increased. This ext d indicates that l can be used to increase the input coupling -60 of the ﬁlter, if wideband responses are needed. On the other hand, the plot shows that the slope is greater when the semi- -70 axis of the air-hole (r ) is larger. Therefore, the sensitivity of 3.5 4 4.5 5 the input coupling with the length (l ) will be stronger for Frequency (GHz) narrowband responses. The plot also indicates that the effect tends to saturate for lengths l > 8 mm. Further increase d Fig. 5. Frequency responses obtained for the two designed ﬁlters. The legend refers to Fig. 1(a) (air-holes) and to Fig. 1(b) ( -posts). of this length does not translate in substantially higher input r External Q-factor (Q ) Coupling length l (mm) ext s1 Air-hole length 2r (mm) Scattering Parameters (dB) A JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 5 |S | Meas. |S | Meas. -10 |S | Tuned |S | Tuned -20 |S | HFSS |S | HFSS -30 -3.5 -40 Meas. Tuned -4 HFSS -50 -4.5 3.65 3.7 3.75 3.8 -60 3.5 3.6 3.7 3.8 3.9 4 Frequency (GHz) Fig. 7. S-Parameter comparison between measured results directly obtained after manufacturing (circle symbols), measured results after tuning (square symbols) and simulated results obtained with HFSS after introducing losses (triangle and cross symbols) (tan = 0:0053, = 3:8 10 S/m). Inset in the ﬁgure shows details of the measured and simulated minimum insertion Fig. 6. Pieces of the manufactured air-holes ﬁlter, showing the two extended losses within the passband. areas of length (l ) used for alignment of the dielectric block inside the main body. when losses are included in the simulations (triangle and performance of both ﬁlters is essentially the same one, at cross symbols). As we can see, the response obtained directly least from the electrical point of view. Mechanically, however, after manufacturing is in reasonably good agreement with the there are some important differences. First, the dimensions simulations performed with HFSS including losses. of Table I indicate that the total length of the ﬁlter with To include losses in the simulations, we have used for air-holes [Fig. 1(a)] is l = 292:847 mm. For the second tot the ABSplus a loss tangent value equal to tan = 0:0053. ﬁlter [Fig. 1(b)], the data of Table II indicate a total length This value corresponds to the largest value speciﬁed by the of l = 275:016 mm. This conﬁrms that, as previously tot manufacturer (0:0046 < tan < 0:0053) . In addition, for discussed, the ﬁlter based on dielectric posts is more compact the external aluminum housing, the conductivity value used is than the ﬁlter based on air-holes. This can be a convenient ( = 3:8 10 S/m). However, we have veriﬁed that the losses feature for practical applications, where reduction in footprint due to the ﬁnite conductivity of the external housing have very is important. little inﬂuence on the overall insertion loss performance of the ﬁlter. This study conﬁrms that the important contribution of III. EXPERIM ENTAL RESULTS losses is due to the loss tangent of the ABSplus. As observed in the inset of Fig. 7, the minimum insertion loss measured The two ﬁlters designed in the previous section have been inside the passband is IL = 3:7 dB. implemented using a hybrid manufacturing approach. AM has Apart from the insertion losses, the other measured charac- been used for the dielectric parts, while the metallic housings teristics are: center frequency f = 3:671 GHz, and bandwidth have been manufactured using standard CNC milling. The c BW = 117 MHz. Overall, the measured response shows good metallic parts have been manufactured using aluminum, while agreement in terms of central frequency and ﬁlter bandwidth, the dielectric parts have been printed using ABSplus with a as compared to the ideal design speciﬁcations. This is a clear 3D-printer, model Dimension 1200-bst . indication that the relative permittivity of the ABSplus block is The pieces manufactured for the air-hole ﬁlter are shown very close to the nominal value reported by the manufacturer in Fig. 6. As we can see, the housing is manufactured in two ( = 3:55) . On the contrary, the measured minimum pieces, namely, a main body and a top cover. This geometry is r return loss within the passband is worse (RL = 12 dB) than very simple, so a standard CNC milling process can be used. the expected value. In addition, we can clearly see that a The dielectric piece is manufactured with the 3D printer in number of reﬂection poles are not clearly visible. This means one single block, including all resonators and couplings. As a that the ﬁlter is not correctly tuned. In general, this behavior is result, the alignment of the dielectric piece inside the metallic normal with low accuracy manufacturing processes. The return body is extremely simple. The alignment is also facilitated by loss is indeed the most sensitive parameter in the response of the use of the two extended areas of length l = 7 mm at both a microwave ﬁlter. extremes of the piece, as shown in Fig. 6. The measured results, directly obtained from the prototype However, the detuning observed in the return loss response manufactured, are shown in Fig. 7 using circle symbols. can be corrected by introducing tuning screws in the manufac- They are compared with the results obtained with HFSS tured prototype, as shown in Fig. 8. In this case, standard M3 Scattering Parameters (dB) A JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 6 Tuning screw for coupling adjustment Tuning screw for resonance adjustment Fig. 8. Photograph of the manufactured ﬁlter based on air holes (Fig. 1(a)), after assembling. Details of the tuning screws used to compensate for manufacturing errors are also shown. tuning screws were used. As we can see in the ﬁgure, a total of 11 tuning screws have been used for the ﬁne tuning of the ﬁlter. Fig. 9. Pieces of the manufactured ﬁlter with dielectric post resonators. The Six screws are located in the center of the air holes, in order ﬁve dielectric elliptic cylinders are shown already mounted and aligned inside to adjust the couplings. Five more screws are placed in the the empty evanescent waveguide section. middle of the resonators (between two contiguous air holes), to allow for the adjustment of the resonant frequencies of the Alignment pins individual resonators. For the installation of these last screws, the dielectric block has been perforated at the appropriate locations. In this context, it is interesting to note that the perforations will shift the resonances to higher frequencies. The presence of the screws in the resonators, however, will lower the resonant frequencies, thus compensating for the initial frequency shifts. This is the reason why the ﬁnal prototype shown in Fig. 8 can be tuned, keeping the same center frequency as in the original structure without tuning screws. The response of the hardware after tuning is also included in Fig. 7 (with square symbols). Results show that the tuning Dielectric resonator (ABSplus) process was indeed effective. In particular, the ﬁlter has the same center frequency and bandwidth as for the initial Fig. 10. Details of a dielectric cylinder resonator including the two pins speciﬁcations. Furthermore, an almost equiripple return loss incorporated for alignment inside the empty evanescent waveguide section. response has been obtained with a RL = 21 dB. However, the The alignment pins are place along the x^-axis. improvements in the passband response come at the expense of a limited increase in the minimum insertion loss of the ﬁlter within the passband, which now increases to IL = 3:9 dB, as considerations related to the the 3D printing process, the height shown in the inset of Fig. 7. Overall, a good ﬁlter performance and diameter of the pins were selected to be p = 2 mm has been demonstrated with the manufactured prototype. Also, and p = 2 mm, respectively. With these dimensions, we the tuning process has shown to be effective in compensating have veriﬁed with EM simulations that the pins do not have the manufacturing errors introduced by the 3D printing tech- any signiﬁcant inﬂuence on the electrical performance of the nique. structure. The second ﬁlter, based on dielectric posts, as shown in After assembling the dielectric cylinders, the measured Fig. 1(b), has been manufactured using a similar strategy. scattering parameters of the ﬁlter are shown in Fig. 11. Again, the metallic housing is manufactured from aluminum Comparison with respect to the simulated response is also in two pieces, with a main body and a top cover, as shown shown, after including losses in the analysis of the structure. in Fig. 9. In this case, an additional practical challenge is the As we can see, the measured and simulated results show alignment of the ﬁve elliptical dielectric resonators inside the excellent agreement for both center frequency and bandwidth. empty evanescent waveguide section. To meet this challenge, The RL performance inside the passband without tuning is in the 3D printing of the ﬁve dielectric resonators we have better in this case, with a minimum value of RL = 18 dB. included two alignment pins of height p and diameter p , The measured bandwidth at a constant return losses of 20 dB h d respectively, as shown in Fig. 10. Two holes per resonator are is 104 MHz. In addition, the measured minimum insertion then drilled in the bottom wall of the main body, with slightly loss within the passband is (IL = 4:3 dB) (see the inset greater diameter than the alignment pins. The dielectric cylin- of Fig. 11). This insertion loss is only 0:3 dB higher than ders are then simply placed inside the metallic housing by the simulated response using tan = 0:0053 to model the introducing the pins in the corresponding holes. For practical ABSplus plastic, and the conductivity of aluminum for the A JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 7 |S | Meas. Piece 2 |S | Meas. |S | HFSS -20 |S | HFSS Piece 1 Meas. -40 -4 HFSS -5 -60 -6 Fig. 13. Comparison of the dielectric pieces designed for the air-holes ﬁlters 3.6 3.65 3.7 3.75 having different bandwidths. Shown at the bottom is the dielectric piece for the -80 ﬁrst ﬁlter with narrower bandwidth (Piece 1). Shown at the top is the dielectric 3.6 3.8 4 4.2 4.4 4.6 4.8 piece for the new ﬁlter with wider bandwidth (Piece 2). Both pieces have the same length: l = 258:847 mm. Frequency (GHz) ev Fig. 11. Comparison between the measured and simulated S-parameters, for the dielectric posts ﬁlter. Simulations include losses in the dielectric resonators dimension of this ﬁlter (l = 292:847 mm) as compared to 7 tot (tan = 0:0053) and ﬁnite conductivity in the housing ( = 3:8 10 S/m). the dielectric post ﬁlter (l = 275:016 mm). The extracted tot Q values from both ﬁlters are Q = 305:75 and Q = U U U 0 303:57, respectively. This indicates that the solution based on air-holes leads to resonators of slightly higher Q , although at the expense of somewhat larger dimensions. Except for the insertion losses, the performances of the two ﬁlters are very -20 similar, both inside and outside of the passband. In particular, both ﬁlters exhibit very similar measured SFR behaviors, with -3 a ﬁrst spurious band at about 4.9 GHz. -40 As a ﬁnal study, we now show the capabilities of the hybrid manufacturing approach proposed in this work to produce -4 different types of transfer functions without changing the ﬁlter housing. The idea is to use the same housing to generate -60 -5 different transfer functions by manufacturing new dielectric pieces with the 3D printer. To illustrate the basic idea, we now show the design of a new air-hole ﬁlter having the same 3.6 3.65 3.7 3.75 -80 speciﬁcations as before, except for the bandwidth which is 3.6 3.8 4 4.2 4.4 4.6 4.8 increased to BW = 175 MHz. Frequency (GHz) For the design of this new ﬁlter, an important geometrical restriction must be taken into account, namely, that the total Fig. 12. Comparison between measured results of the two manufactured ﬁlters with BW = 120 MHz. Legend refers to Fig. 1(a) (air-holes) and to Fig. 1(b) length (l ) for this second piece must be the same as the one ev ( -posts). The tuned response obtained with screws is used for comparison of the ﬁrst ﬁlter (l = 258:847 mm). In Fig. 13 we show ev in the case of the air-holes ﬁlter. the dielectric piece of the previous design (Piece 1), and we compare it with the dielectric piece of the new design with increased bandwidth (Piece 2). housing. As it happened with the previous design, the loss tangent of the ABSplus plastic seems to be in the upper limit As we can see, the same length (l ) is preserved in both ev reported by the manufacturer (0:0046 < tan < 0:0053) designs. The new dielectric piece (shown on top), however, . Since in this case the agreement between measurements has smaller air holes to allow for larger couplings. The and simulations is good, we did not use any further post- smaller holes also increase the loading effects of the couplings manufacturing tuning mechanism. into adjacent resonators. Consequently, the resonators become physically shorter, thus leading to air holes which are placed Finally, in Fig. 12 we include a comparison between the closer as compared to the ﬁrst design (shown at the bottom). measured responses obtained for the two ﬁlters that we have It is important to note that the total length (l ) can be made manufactured. The response of the air-hole ﬁlter used for this ev equal in both designs because of the additional degree of comparison is the one obtained after tuning with screws (see freedom provided by the length l shown in Fig. 1(a) (distance Fig. 8). Details of insertion losses can be observed in the inset 1 of the ﬁgure. As shown, the ﬁlter based on air-holes has lower between the step discontinuity and the ﬁrst/last air-hole). insertion losses (IL = 3:9 dB) as compared to the dielectric The design procedure for the ﬁlter with increased bandwidth post ﬁlter (IL = 4:3 dB). This can be explained by the larger is the same as previously described. The only difference is that Scattering Parameters (dB) Scattering Parameters (dB) A JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 8 TABLE III FINAL DIM ENSIONS OF THE DESIGNED AIR-HOLES FILTER ACCORDING TO |S | 120 MHz F IG. 1(A), FOR BW = 175 MH Z. |S | 120 MHz -10 Var. Value (mm) Var. Value (mm) Var. Value(mm) |S | 175 MHz l 10 l 8:25 r 6:752 port 1 1 |S | 175 MHz -20 l 7 l 22:059 r 11:702 d 2 2 l 258:847 l 23:255 r 13:623 ev 3 3 l 292:847 l 23:411 r 14 tot 4 x -30 -40 |S | Meas. |S | Meas. -10 -50 |S | Tuned |S | Tuned -20 -60 |S | HFSS 3.6 3.8 4 4.2 4.4 4.6 4.8 |S | HFSS -30 Frequency (GHz) -2.5 Fig. 15. Measured S-parameter responses of the two air-holes ﬁlters with -40 Meas. different bandwidths. Responses are shown in a large frequency span to -3 Tuned monitor the out of band performances. HFSS -50 -3.5 3.6 3.7 3.8 3.9 this simulation the losses are characterized using the same -60 parameters as described in the previous examples. As we can 3.5 3.6 3.7 3.8 3.9 4 4.1 see, the losses predicted by the software tool are very similar to Frequency (GHz) those measured directly after manufacturing, while the tuned prototype shows increased losses due to the effects of the Fig. 14. Response of the air-holes ﬁlter designed with wider bandwidth (BW = 175 MHz). Measured results directly after manufacturing (circle tuning screws. symbols) are compared to results obtained after tuning (square symbols), A ﬁnal comparison between the two air-holes ﬁlters with and with simulated results obtained with the software tool HFSS (triangle symbols). different bandwidths is presented in Fig. 15. The measured responses after tuning have been selected for this comparison. We can clearly see the differences in bandwidth between the new coupling and Q curves (similar to Fig. 2 and Fig. 3) two ﬁlters. In both cases the return loss performance is very ext are obtained using (3) and (4) with the new bandwidth (BW ) satisfactory (better than RL = 20 dB). The ﬁlter responses are speciﬁcations. The ﬁnal dimensions for this ﬁlter, as deﬁned shown in a large frequency span, so that the SFR performances in Fig. 1(a), are collected in Table III. can be observed. As we can clearly see, the ﬁrst spurious band again appears at f 4:8 GHz for both ﬁlters, giving The new ﬁlter is obtained by replacing the dielectric Piece 1 sp SFR 1 GHz. with the dielectric Piece 2 inside the same metallic housing (shown in Fig. 6). The measured response obtained directly Overall, the results presented in this paper clearly show after manufacturing is shown in Fig. 14 (circle symbols). that the hybrid CNC milling and 3D printing manufacturing concept that we propose can be used to obtain ﬂexible and low In general, the performance obtained is quite good in terms cost microwave ﬁlters with acceptable electrical performances. of center frequency and bandwidth (f = 3:71 GHz, BW = The only drawback is to have slightly higher values of inser- 180 MHz). The minimum insertion loss inside the bandwidth tion losses. However, we expect that this drawback may be is now lower due to the larger bandwidth (IL = 2:5 dB). eliminated once better quality 3D printing materials become In addition, the return losses are also good, being better than commercially available. RL = 15 dB inside the useful bandwidth. In order to improve the return loss performance of the ﬁlter, we have also used similar tuning screws as previously described (see Fig. 8). IV. C ONCLUSIONS The response obtained after tuning is also shown in Fig. 14 (square symbols). As we can see, after the tuning process we The main aim of this work is to show experimentally that the have a passband with a center frequency of f = 3:687 GHz, use of 3D-printed ABSplus as dielectric material for the design and a bandwidth of BW = 172 MHz. The measured results of evanescent bandpass ﬁlters at C-band is indeed viable. For also show an almost equiripple response with return losses this purpose, two ﬁlter structures using dielectrics and evanes- better than RL = 21 dB. These improvements in the passband cent waveguide housings have been designed, manufactured again come at the expense of an increased insertion loss. The and successfully measured. Both ﬁlters are based on an in-line minimum insertion loss within the passband is IL = 3 dB. For topology, and combine low cost additive manufactured parts comparison, the simulated response obtained with the software for the dielectrics with milled metallic parts for the external tool HFSS is also included in Fig. 14 (triangular symbols). For housing. Scattering Parameters (dB) Scattering Parameters (dB) A JOURNAL OF LT X CLASS FILES, VOL. XX, NO. X, MAY 2019 9 The ﬁrst ﬁlter, based on air-holes, exhibits larger (Q ) value  N.-H. Tran, V.-N. Nguyen, A.-V. Ngo, and V. Nguyen, “Study on the effect of fused deposition modeling (FDM) process parameters on as compared to a solution based on dielectric posts. However, the printed part quality,” Int. Journal of Engineering Research and the second option leads to more compact structures, and to Application, vol. 7, no. 12, pp. 71–77, December 2017. the possibility of achieving higher bandwidths. The capability  C. Carceller, F. Gentili, D. Reichartzeder, W. Bsch, and M. Schwenten- wein, “Practical considerations in the design of monoblock TM dielectric of implementing different transfer functions, by 3D printing resonator ﬁlters with additive manufacturing,” in 2017 International several different dielectric pieces which are then integrated Conference on Electromagnetics in Advanced Applications (ICEAA), inside the same housing, has also been demonstrated. The Sep. 2017, pp. 364–367.  Y. Marchives, N. Delhote, S. Verdeyme, and P. M. Iglesias, “Wide- measured electrical performances are satisfactory, but with band dielectric ﬁlter at C-band manufactured by stereolithography,” in slightly higher insertion losses due to the electrical proper- Microwave Conference (EuMC), 2014 44th European, Oct. 2014, pp. ties of the employed ABSplus plastic. It is expected that 187–190.  A. Perigaud, O. Tantot, N. Delhote, S. Verdeyme, S. Bila, and D. Bail- improvements in insertion loss can be achieved as new 3D largeat, “Bandpass ﬁlter based on skeleton-like monobloc dielectric printing materials, with improved electrical properties, become pucks made by additive manufacturing,” in 2018 48th European Mi- commercially available. crowave Conference (EuMC), Sep. 2018, pp. 296–299.  Stratasys. (2016, August) Absplus datasheet. [Online]. Avail- From the results of this work, we conclude that the hybrid able: http://usglobalimages.stratasys.com/Main/Files/Material Spec CNC milling and 3D printing manufacturing approach demon- Sheets/MSS FDM ABSplusP430.pdf strated in this paper is, indeed, a very valuable industrial tool  A. Pons-Abenza, A. Alvarez-Melcon, F. D. Quesada-Pereira, and L. Arche-Andradas, “Frequency correction design technique for additive for the rapid and ﬂexible prototyping of practical microwave manufactured cavity ﬁlters,” in 2018 48th European Microwave Confer- ﬁlters. ence (EuMC), Sep. 2018, pp. 288–291.  G. Matthaei, L. Young, and E. Yones, Microwave Filters, Impedance Matching Networks, and Coupling Structures. Boston, Massachusetts, REFERENCES USA: Artech House, 1980.  V. Boria and B. Gimeno, “Waveguide ﬁlters for satellites,” IEEE Microw.  ANSYS, “HFSS version 19.2,” https://www.ansys.com/products/ elec- Mag., pp. 60–70, October 2007. tronics/ ansys-electronics-desktop, 2019.  R. J. Cameron, C. M. Kudsia, and R. R. Mansour, Microwave Filters  Stratasys. (2017, May) Dimension 1200es 3D printer. [Online]. for Communication Systems: Fundamentals, Design and Applications. Available: http://www.stratasys.com/es/impresoras- 3d/design-series/ John Wiley, Sons; Inc. Hoboken, New Jersey, 2018, 2nd ed. dimension-1200es  X. Shang, M. Lancaster, and Y.-L. Dong, “W-band waveguide ﬁlter based on large TM120 resonators to ease CNC milling,” Electron. Lett., vol. 57, no. 7, pp. 488–490, March 2017.  M. D’Auria, W. J. Otter, B. T. W. Gillatt, C. Long-Collins, N. M. Ridler, and S. Lucyszyn, “3-D printed metal-pipe rectangular waveguides,” IEEE Trans. Compon. Packag. Manuf. Technol., vol. 5, no. 9, pp. 1339– 1349, September 2015.  O. A. Peverini, M. Lumia, F. Calignano, G. Addamo, M. Lorusso, E. P. Ambrosio, D. Manfredi, and G. Virone, “Selective laser melting manufacturing of microwave waveguide devices,” IEEE Proc., vol. 105, no. 4, pp. 620–631, April 2017.  F. Calignano, D. Manfredi, E. P. Ambrosio, S. Biamino, M. Lombardi, E. Atzeni, A. Salmi, P. Minetola, L. Iuliano, and P. Fino, “Overview on additive manufacturing technologies,” IEEE Proc., vol. 105, no. 4, pp. 593–612, April 2017.  J. R. Montejo-Garai, I. O. Saracho-Pantoja, C. A. Leal-Sevillano, J. A. Ruiz-Cruz, and J. M. Rebollar, “Design of microwave waveguide devices for space and ground application implemented by additive manufactur- ing,” in 2015 International Conference on Electromagnetics in Advanced Applications (ICEAA), Sep. 2015, pp. 325–328.  S. Khan, N. Vahabisani, and M. Daneshmand, “A fully 3-D printed waveguide and its application as microﬂuidically controlled waveguide switch,” IEEE Trans. Compon. Packag. Manuf. Technol., vol. 7, no. 1, pp. 70–80, January 2017.  K. Y. Chan, R. Ramer, and R. Sorrentino, “Low-cost ku-band waveguide devices using 3-D printing and liquid metal ﬁlling,” IEEE Trans. Microw. Theory Techn., vol. 66, no. 9, pp. 3993–4001, September 2018.  J. A. Lorente, M. M. Mendoza, A. Z. Petersson, L. Pambaguian, A. A. Melcon, and C. Ernst, “Single part microwave ﬁlters made from selective laser melting,” in Microwave Conference, 2009. EuMC 2009. European, Sep. 2009, pp. 1421–1424.  C. Guo, X. Shang, J. Li, F. Zhang, M. J. Lancaster, and J. Xu, “A lightweight 3-D printed X-band bandpass ﬁlter based on spherical dual- mode resonators,” IEEE Microwave and Wireless Components Letters, vol. 26, no. 8, pp. 568–570, Aug 2016.  C. Guo, X. Shang, M. J. Lancaster, and J. Xu, “A 3-D printed lightweight X-band waveguide ﬁlter based on spherical resonators,” IEEE Microwave and Wireless Components Letters, vol. 25, no. 7, pp. 442–444, July 2015.  P. Booth and E. V. Lluch, “Enhancing the performance of waveguide ﬁlters using additive manufacturing,” IEEE Proc., vol. 105, no. 4, pp. 613–619, April 2017.  K. Salonitis, G. Tsoukantas, P. Stavropoulos, and A. Stournaras, Virtual Modelling and Rapid Manufacturing - Advanced Research in Virtual and Rapid Prototyping. CRC Press, Jan. 2003.
http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.pngElectrical Engineering and Systems SciencearXiv (Cornell University)http://www.deepdyve.com/lp/arxiv-cornell-university/design-and-implementation-of-evanescent-mode-waveguide-filters-using-Y7P4mVGYJH
Design and Implementation of Evanescent Mode Waveguide Filters Using Dielectrics and Additive Manufacturing Techniques